ENGINE ACCESSORIES · 111 KEY: Blue Item # = New | Red Item # = Hazardous | v Oversize | * While Supplies Last Item# Dia. Case 50-28510w 13 1/2" 10 • Polypropylene • Finger grips • Dish - 3 7/8" • U.V. resistant • Fits all standard 3/4" tapered shafts • Meets NMMA, ABYC and IMCI standards 4 SPOKE STEERING WHEEL Item# Dia. Case 50-28611w 13 1/2" 5 • 304 Stainless steel steering wheel • Fits standard 3/4" tapered shafts • Stainless steel center cap included • Finger grip and large turning knob 3 SPOKE STAINLESS STEEL STEERING WHEEL WITH TURNING KNOB Item# Dia. Case 50-28481w 13 1/2" 5 50-28531w 15 1/2" 5 Repl. Parts Description Size Case 50-28431w Replacement Nut 12mm 12 50-28441w Replacement Nut 1/2"-20 12 50-28461w Replacement Nut 5/8"-18 12 • Stainless steel fits 3/4" tapered shaft • Includes 5/8" - 18 and 1/2" - 20 nut 3 SPOKE SPORTS STEERING WHEEL WITH TURNING KNOB Item# Case 50-28521w 12 Easily converts existing Destroyer wheels to the most modern versions. Installation tool included. Fits Destroyer wheels only. STAINLESS TURNING KNOB Item# Case 50-28491w 12 Easily converts existing Destroyer wheels to the most modern versions. Attractive and durable black plastic center. Fits Destroyer wheels only. LARGE STAINLESS STEEL TURNING KNOB Item# Case 50-28011w 12 • Attaches to outboard steering cylinders for trailering-reduces pressure on cylinder • Attached cord for easy removal and storage of clips • Clips are made of thermoplastic rubber • High visible color acts as a reminder to remove before use OUTBOARD HYDRAULIC STEERING LOCK In use Item# Description Fastener Case 50-28401w Twin Lever Control # 10 screws 6 50-28411w Red Knob 12 50-28421w Black Knob 12 Made of chrome plated brass. Each separate lever controls clutch and throttle for one engine. Functions easily identified by red and black knobs. Designed to use 33C type control cables. Shims and cable clamps are made of brass and are supplied for easy installation. Overall height 8 5/16" Base: 4 5/16" W x 5 7/16" L x 3" H Not for dual station applications. TWIN LEVER, SINGLE STATION CONTROL Item# Pack Case 50-28501w 2 12 Pair of stainless steel and plastic pulleys with two stamped stainless steel eye straps. Maximum rope size: 1/4". OD of sheave: 2 5/16". 4 1/2" overall length. TILLER ROPE PULLEY Item# Pack Case 50-28601 2 12 For use with 1/8" or 3/16" rope. Chrome plated zinc. Dimensions: 1 1/4" x 11/16". TILLER ROPE CLAMP Item# Case 50-28131w 12 Provides a weatherproof tilt control system at the stern area of the boat. Can be used for remote adjustment of hydraulic plates. 18" Marine grade tinned wiring harness included. TRANSOM TRIM CONTROL Item# Pack Case 50-90391 2 12 • Cleans tilt tubes • For use with electric drills • Sold in pairs STEERING TUBE CLEANING BRUSH Item# Size Case 50-28251 7/8" 12 50-28261 1" 12 The Steering Guard should be installed on all cable and side-mounted hydraulic steering systems to lubricate, clean and seal the system. Will more than double the life of a new cable system. Made of stainless steel. Installs in 10 minutes. Eliminates greasy steering rods forever. 28251: Fits Honda, Mercury, Mariner, Johnson, Evinrude, Nissan, Suzuki, Tohatsu, Yamaha and Force with 7/8" thread. 28261: Fits Honda, Mercury, and Mariner with 1" thread. STEERING GUARD Item# Case 50-28301w 10 Heavy-duty rubber boot to fit over output end of steering cable at engine for complete protection from elements and preventing lubrication from being washed away. Fits all standard steering cables including Morse, Teleflex, Detmar, etc. Dimensions: 1" ID steering cable end, 3/8" ID output end, 1 1/2" overall diameter, 10" extended length, 3 1/2" minimum length. STEERING CABLE PROTECTOR
RkJQdWJsaXNoZXIy MTI2MTky